Ring lead screen allowing directional shot and centering rods kit.

Most of your work is done with a panoramic tube but sometimes a directional beam would be useful? This ring lead screen is your solution.

• Ring lead screen available for all panoramic generators from Baltospot series
• Allows directional shot for panoramic generators
• Centering devices kit available
• Easy to install

The protective cradle provides good protection for directional generators against shocks and simplifies their handling. It can be easily turned into a four leg stand or adapted to the hydraulic stand.

Available for all Baltospot generators.

• Cradle available for all generators from Baltospot serie
• Protection of the generator against shocks
• Easy to install
• Adaptable for FLS02 stand

Power generator 4.2 KVA single 50 Hz 230V 3200 Watts - fuel

Thanks to our equipments ready to work on power generator, Balteau provides a solution to work in every environement, even when there is no power available.

• 3200W Power generator
• Fuel type SP98-E5
• 2 plugs type 2P+T 230V 10/16A

A centering device for directional Baltograph tubeheads is available in the accessories. The centering device allows for a laser pointer or a telescopique centering device but will be also used to install a lead obturator and diaphragms on the tubehead. All Baltograph directional tubeheads are supported, contact us for other brands.

• Available for directional Baltograph tubes
• Laser or telescopique centering devices available
• Support for lead obturator and diaphragms
• Available for other brands of tubeheads

For collimation purpose, diaphragms can be purchased for all directional Baltospot & Baltograph units. A diaphragm is made of steel and is available with different dimensions of aperture. A diaphragm will be a great tool to collimate the x-ray beam and avoid blooming effect.

• Available for directional Baltospot generators and Baltograph tubes
• Made of steel and lead
• To avoid blooming effect

For preheating purpose, a lead obturator can be purchased for all Baltospot & Baltograph units. A obturator is made of steel and lead stopping the X-ray exposure on the component to be inspected. A lead obturator is also a great accessory when it comes to digital radiography, stopping the x-ray beam will protect the digital detector from premature aging.

• Available for Baltospot and Baltograph
• Made of steel and lead
• Protection for digital detectors

Balteau NDT also offers Transport case for all Baltospot equipment allowing an easy transport but also a good protection for the equipment and makes it practicle for storage.

All parts of the equipment will fit in the Transport case, such as generator, control unit, cables, cradle, fls-02, etc.

• All part of the equipment fitting in the transport case
• Handles for easy transport
• Robust with sides and corner protections
• Light weight
• Available for all Baltospot generators

All generators can be equipped with a Clignotix, a warning flashing light connected to the equipment designed to make people visually aware of an ongoing x-ray exposure within the area. The Clignotix is a device designed to work with Balteau NDT ranges such as Baltospot and Baltograph. Several Repeaters can be added to the Clignotix allowing more than one point of flashing light.

• Works with Baltospot & Baltograph generators
• Driven by the control units
• Several repeaters in option
• Red flashing led light
• 20 meters cable as standard

The AVARA/P is an Audible & Visible Automatic Portable Radiation Alert, part of a complete range of Balteau products dedicated to Safety, Measurements and Quality improvement.

An accurate monitoring of the radiation level in a controlled area is most of the time a legal obligation but also an essential measure in order to protect the people around.
The basic Safety principles of Radio protection (ALARA – As low as reasonably achievable) must always be followed when performing an exposure not only in the parameters selection, but also in the exposure settings.

AVARA/P is a stand alone detector allowing the operator to monitor closely the working area. As soon as the unit detects X or Gamma radiation, an audible and visible alert informs the operator that the zone where the unit is located is being irradiated. AVARA/P is the unavoidable tool for an efficient control of a specific area in order to guarantee a maximum security to the operator and other people standing close to the working zone.

• Monitoring instrument
• Audible alarm (can be heard up to 35m)
• Visible alarm
• Portable radiation alert
• Works for the X & gamma radiation
• Increase security
• Auto-check led
• Geiger-Müller detector
• Orange flash when the AVARA is ready
• Red flash when radiation detected

• Flexibility and mobility
• Designed to be used on field
• Efficient on field
• Can work independently
• Small size and light
• Robust (protection : casing)
• Ergonomic handle
• Rechargeable battery
• Data retrieving (RS232 connector)

The AVARA/C is part of a complete range of BALTEAU NDT products dedicated to Safety, Measurements and Quality improvement.

An accurate monitoring of the radiation level in a controlled area is most of the time a legal obligation but also an essential measure in order to protect the people around. The basic Safety principles of Radio protection (ALARA – As low as reasonably achievable) must always be followed when performing an exposure not only in the parameters selection, but also in the exposure settings.

AVARA/C is a radiation detector linked to a shielded cabinet allowing the operator to monitor closely the working area. As soon as the unit detects X or Gamma radiation, an audible and visible alert informs the operator that the zone where the AVARA is located is being irradiated.

AVARA/C is the unavoidable tool for an efficient control of a specific area in order to guarantee a maximum security to the operator and other people standing close to the working zone.

• Monitoring instrument
• Audible alarm (can be heard up to 35m)
• Visible alarm
• Radiation alert for shielded cabinet
• Works for the X & gamma radiation
• Increase security
• Auto-check led
• Geiger-Müller detector
• Orange flash when the AVARA is ready
• Red flash when radiation detected

• Flexibility
• Small size and light
• Data retrieving (RS232 connector)
• Smart

COSIX is managing all the safety functionalities and warnings in your RT facilities. According to international rules, operating an industrial X-ray equipment requires to connect the unit to visible and audible alerts.

On the other hand, using multiple X-ray generators or even Gamma projectors in the same inspection room involves connection and compatibility difficulties that may lead to a physical hazard for the end users. COSIX is the universal answer developed by Balteau to meet these legal aspects and anticipate future needs. COSIX is an essential safety device that can be connected to a large variety of X-ray equipments as well as various safety elements such as door security switches, motion sensors, emergency buttons, buzzers…

As an option, our independent radiation detection device, the AVARA, can be directly connected and displayed by the COSIX. The real time monitoring of the status of all safety devices of your inspection room is continuously ensured.

• Roundsman interface with GM detectors
• Multiple equipment connection
• Doors detectors connection
• Audible alarm & radiation Alert ready (Avara/C)
• Visible alarm (Clignotix)
• Works for the X & gamma radiation
• Increase security
• LED status indicators & LCD screen
• Geiger-Müller detector (With Avara/C)
• Red flash when radiation detected

• High security improvement
• Answers new regulations requirements
• Rackable design
• Up to 5 generators entry
• 7 independant safety loops CAT. 2
• Connection for 2 doors, 2 emergency
• stops, 2 PIR sensors, 1 Avara/C
• Data retrieving (RS232 connector)

X-ray beam size and shape is defined by the inherent construction of the Tube. The way the target is positioned, the shielding and housing designs are largely influencing the beam cone, but this is fixed and sometimes not adequate to the imaging detector or Shielding environment. The use of a collimator is then very useful when you want to precisely control the cone shape and extent.

The collimator acts as a mobile window reducing or defining the limits of the beam to the detector sizes or portion of area to be covered.

Made out of highly absorbing material, shutters are remotely moved with electric motors operated from the control room.

• Delivered with Diaphragm Remote Control (DRC) software from the Baltoscope Inspection suite
• Lead shutter edge machined (perfect contact)
• Lead shutter driven by DC motors (with driver)*
• 2 mm Al filter fixed (with a screw) on the front side

• Position encoder for the lead shutters
• Other front filter material
• Rack for filters attachment
• Other cable lengths

The LED Film Viewer has introduced LED technology to radiography. The efficiency of LED’s is much more higher than halogen lamps because they create only ‘cold’ light without
heat radiation. With only low heat to be removed, the fan on the film viewer is now whisper quiet.

The high luminance of the LED viewing units requires hundreds of single light sources leading to a uniform light distribution on the screen. With an expected life of more than 40,000 hours, a viewer’s light source should last around 20 years if operated 40 hours per week.

• Luminance 125,000 cd/qm
• Suitable for large radiographs of castings
• Comfort of use : interpretation easier
• Mask for 6cm wide films
• Specific shape viewing
• Low voltage LED lamps (brigther and higher rendering than conventional bulbs)
• power line cable and foot switch cable

• Luminance of 125,000 cd/qm
  For density up to D= 4.1 in accordance to:
  - EN 25580
  - ISO 5580
  - ASTM E 1390
• Housing: Powder coating
• Additional mask for 6 cm wide films
• Continuous brightness control from 5 to 100%

This unit combines a large viewing area and a very bright light output. Thanks to its unique combination of an infrared filter and a diffusion filter, the film never gets too much heat from the powerful lights but also the light density of the viewing surface is constant all through the area. Halogen lights are providing the right white colour shade for improving viewing comfort of the inspector.

A sturdy remote foot switch gives the operator the possibility to adapt light to density of the film in an easy and convenient way.

• Extreme luminance
• Suitable for large radiographs of castings
• Comfort of use : interpretation easier
• Masks
• Specific shape viewing
• Low voltage 24 lamps switch (brigther and
• higher rendering than conventional bulbs)
• Low voltage triple transformers

• Coating: Synthetic resin enamel
• Three additional masks with positioning
• brackets:
  - 5 x 18 cm
  - 8,5 x 18 cm
  - 12 x 18 cm
• Electronic brightness control: 0 to 100%

The Direct View Pocket Dosimeter is part of Balteau NDT Accessories range. It has been designed to measure and read accumulated dose of X-Ray and Gamma radiation exposure.

As every equipment delivered by Balteau NDT, the Direct View Pocket Dosimeter is built to satisfy the highest requirements such as military specifications for the IM-Series RADIAC METER and ANSI N13.5 and N322.

It is hermetically-sealed, immersion proof and can be attached to anything that needs radiation monitoring, thanks for the metal clip attach.

• Lightweight
• Sturdy metal pocket clip
• Hermetically-sealed and waterproof
• Available with with protective hard
• saphire window to prevent lens from
• being scratched
• For X-Ray and Gamma radiation
• Dose rate independant for X-Ray and
• Gamma
• Fiber Electrometer detector mounted in an electrical conductive plastic chamber
• Very low permeability plastics

• Specifications: ANSI N13.5 / ANSI N322 - 1997
• Dose rate independant for X-Ray & Gamma
• Finish Natural Matte Black with a metal clip

The APU 3000 sets the standard for quality, consistency and case of use in x-ray film processing.

The proposed combination of reliable performance, rapid throughput, daylight processing, simple operation, minimal maintenance, compact dimensions and flexibility in films and chemistry is unrivalled.

The APU 3000 processing is the cost effective choice for each x-ray film developer.

• Intermediate wash between developer
• Progammable Microprocessor
• Sensorbar for exact detection of film area
• Anti-oxidation/Standby replenishment cycles
• Anti-crystalisation cycles
• Standy mode
• Inline Heat exchanger
• Warm air dryer
• Flexibility of films and chemistry (Films of different size and type can be processed)
• Visual warning of low chemicals
• Rapid processing (dry radiographs in 2,7 min)
• Fully automatic processing

• Extened & covered film tray
• Open stand (Foot raiser)
• Panel covers for open stand
• Water supply panel
• Exhaust fan 2 x 100 mm
• External chiller assembly

PEX is a Pocket Exposure Assistant designed by Balteau NDT and made for Safety, Measurements and Quality improvement.

PEX is the ideal companion for every field radiographer but also for lab applications.

This unit has been developed to provide all the necessary tools all along the Radiographic exposure and even untill the processing of the film ; in a single small compact ergonomic casing. Menu operation is very easy to use as only one central mini Joystick is driving you all through operations with the use of a single thumb.

• Eliminates the risks of retaked due to calculation errors
• Compact unit
• Gives you the right exposure time
• Easy to use
• Simple menu
• Possibility to update the PEX firmware
• Reduces the number of small equipment needed
• Countdown timer
• Isotope database
• Backlight display to facilitate the reading of messages

• Countdown timer: three channels independent, Start-Pause-Stop
• Timer accuracy: 1 second
• Distances : mm, inches
• Activity: Ci, GBq
• Converter tool: According to SI standard recommendation
• Connectivity: RS232 connection for software and data upload & USB optional
• Warranty: Limited 2 years